Part A
ADIS16210CMLZ
Компания Analog Devices Inc.
- Lifecycle
- Active
- Stock
- 5236 ПКС
- Package
- TERMINAL-15
- Series
- Датчики движения - наклонометры
Replacement verdict
Not a drop-in replacement
The ADIS16365BMLZ and ADIS16210CMLZ are not drop-in replacements for one another. Although both are Analog Devices iSensor inertial measurement units sharing a comparable module form factor and SPI interface, they differ fundamentally in integrated sensor set, dynamic range, and output data configuration, so a direct board-level swap is not supported without validation of the host system's mechanical, electrical, and firmware requirements.
Different sensor configuration
Different dynamic range
Different output data format
Firmware revalidation required
Parts at a glance
Part B
ADIS16365BMLZ
Компания Analog Devices Inc.
- Lifecycle
- Active
- Stock
- 6623 ПКС
- Package
- Module
- Series
- Датчики движения - IMU (инерционные измерительные единицы)
Key differences
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADIS16365BMLZ | ADIS16210CMLZ | Why it matters |
|---|---|---|---|
| Sensor Type / Function | Six degrees of freedom inertial sensor (3-axis gyroscope + 3-axis accelerometer) | Inclinometer / tilt sensor (3-axis accelerometer with incline output) | Defines the core measurement function; a 6-DOF IMU and an inclinometer are not functionally interchangeable for motion/attitude sensing applications. |
| Gyroscope Measurement Range | ±300°/sec (configurable) | Not applicable (no gyroscope) | The presence or absence of a gyroscope determines whether angular rate sensing is possible, which is critical for stabilization and navigation. |
| Accelerometer Measurement Range | ±18 g | ±1.7 g (incline measurement range ±180°) | Different full-scale ranges affect the ability to measure high-dynamic acceleration versus precise low-g tilt/incline sensing. |
| Output Interface | SPI (serial peripheral interface) | SPI (serial peripheral interface) | Both use SPI, so host-side digital communication is compatible, easing electrical integration even though sensor functions differ. |
| Supply Voltage | 4.75 V to 5.25 V | 3.0 V to 3.6 V | Different supply rails require different power design; a 5 V system cannot directly host the 3.3 V part without regulation. |
| Package / Footprint | Module, 23.2 mm × 23.2 mm × 23.0 mm (ML-24 package) | Module, 15.2 mm × 15.2 mm × 15.0 mm (ML-16 package) | Physical size and mounting differ, so a drop-in mechanical replacement is not possible without redesign. |
| Operating Temperature Range | −40°C to +105°C | −40°C to +85°C | The wider temperature range of the IMU suits harsher environments; the inclinometer is limited to standard industrial conditions. |
| Primary Application | Motion sensing, stabilization, navigation, platform control | Tilt/incline measurement, leveling, platform inclination monitoring | Application fit determines substitutability; the two parts target fundamentally different sensing tasks. |
Need help validating a replacement?
Send your BOM and application constraints for technical and sourcing review.
Full specification comparison
Use manufacturer datasheets as the final authority.
| Specification | ADIS16210CMLZ | ADIS16365BMLZ |
|---|---|---|
| Series | iMEMS®, iSensor™ | iMEMS®, iSensor™ |
| Part Status | Active | Active |
| Axis | X, Y, Z | - |
| Measuring Range | ±180° | - |
| Bandwidth | 50Hz | - |
| Voltage Rating | 3 V ~ 3.6 V | - |
| Output Type | Digital | SPI |
| Interface | SPI | - |
| Sensor Type | - | Accelerometer, Gyroscope, 6 Axis |
| Operating Temperature | - | -40°C ~ 105°C (TA) |
Frequently asked questions
What are the primary functional differences between the ADIS16365BMLZ and the ADIS16210CMLZ?
The ADIS16365BMLZ is a six-degree-of-freedom inertial sensor that integrates a triaxial gyroscope and a triaxial accelerometer. The ADIS16210CMLZ is a precision triaxial inclinometer that integrates a triaxial accelerometer and provides calibrated inclination outputs. The ADIS16365BMLZ targets dynamic motion sensing, while the ADIS16210CMLZ targets static and quasi-static tilt measurement.
Are the ADIS16365BMLZ and ADIS16210CMLZ pin-to-pin or package compatible?
No. Both devices are supplied in a 15-lead module package, but their pin functions and internal signal definitions differ because the ADIS16365BMLZ includes gyroscope interfaces and the ADIS16210CMLZ provides inclinometer-specific outputs. A direct PCB drop-in replacement is not supported without verifying the pinout and signal definitions in the respective datasheets.
Can the ADIS16210CMLZ replace the ADIS16365BMLZ in a motion-sensing application?
No. The ADIS16210CMLZ does not integrate gyroscopes and therefore cannot provide angular rate measurements. Applications requiring yaw, pitch, or roll rate data from the ADIS16365BMLZ cannot be served by the ADIS16210CMLZ.
Do both devices use the same digital communication interface?
Both devices provide an SPI-compatible serial interface for configuration and data readout. However, the register maps, output data formats, and command sets differ between the ADIS16365BMLZ and the ADIS16210CMLZ, so firmware and host software must be adapted accordingly.
How do the supply voltage requirements compare between the two devices?
Both the ADIS16365BMLZ and the ADIS16210CMLZ operate from a single 3.3 V nominal supply, with the datasheet-specified operating range of 3.0 V to 3.6 V. Designers should confirm the exact limits and decoupling requirements in each product's datasheet before finalizing the power design.
Which device is better suited for platform stabilization and which for tilt sensing?
The ADIS16365BMLZ, with its integrated triaxial gyroscope and accelerometer, is suited for platform stabilization and dynamic orientation estimation. The ADIS16210CMLZ, with its calibrated inclination outputs, is suited for static or quasi-static tilt and leveling measurements.
Are the ADIS16365BMLZ and ADIS16210CMLZ rated for the same operating temperature range?
Both devices are specified for the industrial temperature range of −40°C to +105°C per their manufacturer datasheets. Users should verify the exact temperature specifications and any derating guidance in the respective datasheets for the target application.