ADM3485EAR vs ADM3491EARZ

Это подробное сравнение ADM3485EAR и ADM3491EARZ предоставляет ценную информацию об их технических характеристиках и ключевых особенностях. Мы подробно рассматриваем важные факторы, включая соответствие требованиям RoHS, статус REACH, серию, способ монтажа, тип корпуса и другие соответствующие характеристики. Представление различий рядом упрощает выбор компонентов, облегчая вам выбор оптимального варианта для вашего конкретного применения.

Technical review by ETEI Component Engineering Source: manufacturer documentation

Replacement verdict

Compatible functional replacement candidate

The ADM3491EARZ and ADM3485EAR are both 3.3 V RS-485/RS-422 transceivers from Analog Devices in the same 8-lead SOIC package, making them a strong functional replacement candidate. The ADM3491EARZ offers full-duplex operation with a higher maximum data rate and enhanced ESD protection, while the ADM3485EAR is a half-duplex device. Designers must confirm the duplex configuration and data rate requirements of the target application before substituting, but the shared supply voltage, package footprint, and transceiver function support a viable drop-in candidate pending validation of the duplex and speed differences.

Duplex Configuration Validation required
Maximum Data Rate Validation required
Package Type High match
Supply Voltage High match

Parts at a glance

Part A

ADM3485EAR

Компания Analog Devices Inc.

Lifecycle
Active
Stock
3150 ПКС
Package
SOIC-8
Series
Интерфейс - драйверы, приемники, передатчики
Part B

ADM3491EARZ

Компания Analog Devices Inc.

Lifecycle
Active
Stock
5715 ПКС
Package
SOIC-14
Series
Интерфейс - драйверы, приемники, передатчики

Key differences

Rows are prioritized by design impact. Highlighted values require attention during substitution.

Key electrical and mechanical differences between the two devices

Parameter ADM3491EARZ ADM3485EAR Why it matters
Duplex Mode Full duplex Half duplex Full duplex allows simultaneous transmit and receive, while half duplex shares the bus; this fundamentally changes wiring and protocol compatibility.
Number of Drivers / Receivers 1 driver / 1 receiver 1 driver / 1 receiver Both provide a single differential channel, but the duplex difference means the driver/receiver are wired differently on the bus.
Data Rate 12 Mbps 12 Mbps Maximum signaling rate determines throughput capability; identical rates mean similar speed performance.
Supply Voltage 3.0 V to 3.6 V 3.0 V to 3.6 V Operating supply range must match the system rail; both are 3.3 V nominal devices.
Number of Pins / Package 14-lead SOIC 8-lead SOIC Different pin counts and footprints prevent direct drop-in replacement on the same PCB layout.
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C Industrial temperature range suitability is identical, so environmental compatibility is the same.
ESD Protection (Bus Pins) ±15 kV (HBM) ±15 kV (HBM) Robust ESD protection on bus pins improves field reliability; both offer equivalent protection levels.
Fail-Safe Receiver Yes (open/short circuit) Yes (open/short circuit) Fail-safe receivers guarantee a defined logic output when the bus is idle or faulted, preventing spurious data.
Receiver Input Impedance 1/8 unit load (up to 256 nodes) 1/8 unit load (up to 256 nodes) Lower unit load allows more transceivers on a shared bus; both support up to 256 nodes.

Need help validating a replacement?

Send your BOM and application constraints for technical and sourcing review.

Full specification comparison

Use manufacturer datasheets as the final authority.

Specification ADM3485EAR ADM3491EARZ
Part Status Obsolete Active
Type Transceiver Transceiver
Protocol RS422, RS485 RS422, RS485
Number of Drivers/Receivers 1/1 1/1
Duplex Half Full
Receiver Hysteresis 50 mV 50 mV
Data Rate 10Mbps 10Mbps
Voltage - Supply 3V ~ 3.6V 3V ~ 3.6V
Operating Temperature -40°C ~ 85°C -40°C ~ 85°C
Mounting Type Surface Mount Surface Mount

Frequently asked questions

What are the key differences between the ADM3491EARZ and ADM3485EAR?

The ADM3491EARZ is a full-duplex RS-485/RS-422 transceiver with separate driver and receiver enable pins, while the ADM3485EAR is a half-duplex RS-485/RS-422 transceiver with combined driver/receiver enable control. The ADM3491EARZ provides four signal lines (A, B, Y, Z) for full-duplex communication, whereas the ADM3485EAR uses two signal lines (A, B) for half-duplex operation.

Are the ADM3491EARZ and ADM3485EAR pin-compatible?

No. The ADM3491EARZ is offered in a 14-lead SOIC package, while the ADM3485EAR is offered in an 8-lead SOIC package. The pin counts and pin functions differ, so they are not drop-in replacements for each other.

What data rate do the ADM3491EARZ and ADM3485EAR support?

Both devices are specified for data rates up to 12 Mbps, making them suitable for high-speed RS-485/RS-422 communication links.

Do the ADM3491EARZ and ADM3485EAR operate from the same supply voltage?

Yes. Both transceivers operate from a single 3.3 V supply, which allows them to interface directly with 3.3 V logic without level shifting.

How do the fail-safe features of the ADM3491EARZ and ADM3485EAR compare?

Both devices include true fail-safe receiver inputs, ensuring a known logic-high receiver output when the inputs are open, shorted, or terminated but undriven. This prevents indeterminate output states during idle or fault conditions on the bus.

What ESD protection do the ADM3491EARZ and ADM3485EAR provide?

Both devices feature enhanced ESD protection on the RS-485/RS-422 bus pins, specified to withstand ±15 kV using the Human Body Model (HBM), which helps protect the transceivers in harsh industrial environments.

Which device should be selected for full-duplex versus half-duplex applications?

The ADM3491EARZ should be selected for full-duplex applications requiring simultaneous transmit and receive over separate twisted pairs. The ADM3485EAR is appropriate for half-duplex applications where a single twisted pair is shared for transmit and receive, reducing cabling and cost.

Are the ADM3491EARZ and ADM3485EAR specified over the same operating temperature range?

Yes. Both devices are specified for the industrial temperature range of −40°C to +85°C, supporting use in industrial automation, instrumentation, and other demanding environments.