ADM4853ARZ
Компания Analog Devices Inc.
- Lifecycle
- Active
- Stock
- 6517 ПКС
- Package
- SOIC-8
- Series
- Интерфейс - драйверы, приемники, передатчики
Это подробное сравнение ADM4853ARZ и ADM4851AR предоставляет ценную информацию об их технических характеристиках и ключевых особенностях. Мы подробно рассматриваем важные факторы, включая соответствие требованиям RoHS, статус REACH, серию, способ монтажа, тип корпуса и другие соответствующие характеристики. Представление различий рядом упрощает выбор компонентов, облегчая вам выбор оптимального варианта для вашего конкретного применения.
Replacement verdict
The ADM4853ARZ and ADM4851AR are both half-duplex RS-485/RS-422 transceivers from the same Analog Devices family, sharing an identical 8-lead SOIC footprint and the same 5 V supply and industrial temperature range. The ADM4853ARZ offers higher maximum data rate and full fail-safe receiver behavior, while the ADM4851AR provides a lower slew-rate-limited option. Both are functionally interchangeable in most RS-485 bus designs, with the primary distinction being data rate and fail-safe requirements rather than pinout or electrical interface.
Компания Analog Devices Inc.
Компания Analog Devices Inc.
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADM4853ARZ | ADM4851AR | Why it matters |
|---|---|---|---|
| Data Rate | 500 kbps | 500 kbps | Maximum signaling speed; both support the same rate, so timing compatibility is equivalent. |
| Duplex Mode | Full duplex | Half duplex | Full duplex allows simultaneous transmit/receive on separate pairs, while half duplex shares one pair; this fundamentally changes bus wiring and protocol design. |
| Number of Drivers/Receivers | 1 driver / 1 receiver | 1 driver / 1 receiver | Determines how many bus lines can be driven and sensed; identical here, so node count per device is the same. |
| Receiver Input Impedance (Unit Loads) | 1 unit load (12 kΩ) | 1 unit load (12 kΩ) | Unit-load rating sets the maximum number of nodes on a bus; both are 1 UL, allowing up to 32 standard nodes. |
| Supply Voltage | 5 V | 5 V | Operating supply must match the system rail; both require a single 5 V supply. |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C | Defines environmental limits for reliable operation; identical industrial temperature range. |
| Package / Mounting | 8-SOIC (surface mount) | 8-SOIC (surface mount) | Footprint and assembly compatibility; both use the same 8-lead SOIC package, enabling drop-in PCB placement. |
| Fail-Safe Receiver | Yes (open/short fail-safe) | Yes (open/short fail-safe) | Fail-safe biasing guarantees a defined logic state when the bus is idle or disconnected, preventing spurious data; both provide it. |
| ESD Protection (Bus Pins) | ±15 kV (HBM) | ±15 kV (HBM) | Bus-pin ESD robustness affects field reliability; both offer the same ±15 kV human-body-model protection. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | ADM4853ARZ | ADM4851AR |
|---|---|---|
| Supplier | - | Rochester Electronics, LLC |
| Part Status | Active | Obsolete |
| Type | Transceiver | Transceiver |
| Protocol | RS422, RS485 | RS422, RS485 |
| Number of Drivers/Receivers | 1/1 | 1/1 |
| Voltage - Supply | 4.75V ~ 5.25V | 4.75V ~ 5.25V |
| Mounting Type | Surface Mount | Surface Mount |
| Duplex | Half | - |
| Receiver Hysteresis | 20 mV | - |
| Data Rate | 10Mbps | - |
| Operating Temperature | -40°C ~ 85°C | - |
The ADM4853ARZ is a half-duplex RS-485/RS-422 transceiver specified for data rates up to 10 Mbps, while the ADM4851AR is a half-duplex RS-485/RS-422 transceiver specified for data rates up to 500 kbps. Both are 5 V single-supply devices in 8-lead SOIC packages, but they differ in maximum data rate, slew-rate limiting, and quiescent supply current.
Yes. Both devices are offered in the same 8-lead SOIC (R-8) package with the same pinout: RO, RE, DE, DI, GND, A, B, and VCC. This allows a common PCB footprint, but the electrical differences must still be validated for the target design.
The ADM4853ARZ supports data rates up to 10 Mbps, whereas the ADM4851AR supports data rates up to 500 kbps. The ADM4853ARZ is therefore the higher-speed option of the two.
Yes. The ADM4851AR is a slew-rate limited transceiver intended for reduced EMI and lower data-rate applications up to 500 kbps. The ADM4853ARZ is a high-speed device rated to 10 Mbps and is not specified as a slew-rate limited part.
Both devices operate from a single 5 V supply (VCC = 5 V ±5%). They are not 3.3 V parts, so the supply rail must be verified against the target system before substitution.
The ADM4851AR is specified with a lower quiescent supply current than the ADM4853ARZ. The ADM4851AR datasheet lists a quiescent supply current of 300 µA typical, while the ADM4853ARZ is specified at 500 µA typical. Designers should confirm the exact limits in the respective Analog Devices datasheets for worst-case budgeting.
Pin compatibility and the common 5 V supply allow a common footprint, but a direct replacement requires validating the higher 10 Mbps data rate of the ADM4853ARZ against the bus topology, cable length, termination, and EMI requirements of the existing 500 kbps design. The ADM4853ARZ should not be assumed to be a drop-in replacement without this validation.
Both devices are offered in commercial temperature grade versions. The ADM4853ARZ and ADM4851AR are specified over the 0°C to +70°C commercial temperature range. Industrial temperature grade variants exist under different order codes and should be selected separately if required.